Investigations of High Velocity Jet onto Fluidic Part
DOI:
https://doi.org/10.53555/ans.v2i4.99Keywords:
Jet,, Mass transfer, Nanotechnology, Disk Reactor, Fragrance Industry,, Low TemperatureAbstract
Model system of one-many fluids contained in single container is under consideration introducing a high velocity jet at top location onto system of fluids. The mechanism is flow, hit, push, penetrate and replace. There are many actions which are observable and can be included into mechanism. In this work, with introducing high velocity jet, simulations are investigations. Blown jet flow is round enough. Surface of fluid changes its shape. The dip fizzy bubble for various velocity jets is shown. The influence is drawn between the surface dip generated and variation of jet velocity; within phase diffraction occurs. Mass transfer is noted. Fuzzy interfacing is performed to relate jet, continuum phase and absorption too. Such operations are incited to promote the excessive jet-fluid systems.
Downloads
References
Khokhar, Z.H., HabibZughbi, S. Sadiquee, 2003, Investigations of jet injection arrangements into main flow, International conference on chemical and bioprocess engineering, ICCBPE, Aug, Sabah, Malaysia.
.A.M. Rothboce, A. Kbsek and A.W. Jones, 1942, The induction of water to the inlet air as a means of internal cooling inaircraft-engine cylinders.NACA report 756. Au.H20.
H. Lohe, 1966, Heat and mass transfer on top-blowing liquid surfaces. Chemie-Ing.-Techn., 38, 309-314.
L. K. Brumfield and T. G. Theofanous, 1976, Turbulent mass transfer in jet flow and bubble flow: A reappraisal of levich's theory,AIChE J., 22: 607-610
T. Aizawa, M. Kanakubo, Y. Ikushima, N. Saitoh, K. Arai, R.L. Smith Jr., 2004, Totsu.-window optical cell for absorption and emission studies of high-pressure liquids and supercritical fluids, J. Supercrit. Fluids,29,313. 317.
T. Aizawa, Y. Masuda, K. Minami, M. Kanakubo H. Nanjo, R.L. Smith, 2007, Direct observation of channel-tee mixing of hightemperature and high-pressure water, J. Supercrit,Fluids,43,222-227.
C. H. Lin. and E. E. O’Brien, 1974, Turbulent shear flow mixing and rapid chemical reactions: an analogy, J. Fluid Mech., 64, 195.
A. M. Ger and E. R. Holley, 1976, Comparison of single-point injection in pipe flow,J. Hydraul. Div. ASCE, 102 (HY 6), 731.
Zahid Hafeez Khokhar, Investigation of mixing in pipeline with side-, opposed-, and multiple-tees, Thesis, Nov 2002.
Z.H.Khokhar, H.D.Zughbi, R.N.Sharma, 2002, Mixing in pipeline with side-tee, 6th Saudi Engg Conference, Dec, 3-04-021, 2,171-182
Z. H. Khokhar, 2002, Mixing in pipeline with side-tee, 6th Saudi Engg Conference, Dec, Presented.
M. Shilyaev, H. Khromova and S. Shirokova, 2015, The ways of mass transfer intensification in industrial jet scrubbers, In EPJ Web of Conferences (82, 01018). EDP Sciences.
M. Shilyaev, and E. M. Khromova, 2013, Modeling of heat and mass transfer and absorption-condensation dust and gas cleaning in jet scrubbers, Mass Transfer–Advances in Sustainable Energy and Environment Oriented Numerical Modeling.
S. S. Yoon, R. A. Jepsen, M. R. Nissen, T. J. O’Hern, 2007, Experimental investigation on splashing and nonlinear fingerlike instability of large water drops, Journal of Fluids and Structures, 23, 101-115.
Z. Pan, B.S. Wang andZ.P. Song, 2004, Research on underwater rocket separation performance, Journal of Ship Mechanics, 8(4), 22-26.
G. C. Gardner and I. G. Crow, 1973,Onset of entrainment and mass transfer with a jet directed at a two-phase interface,The Chemical Engineering Journal, 5(2), 267-273.
A. A.Sotiriadis, R. B. Thorpe and J. M. Smith, 2005,Bubble size and mass transfer characteristics of sparged downwards two-phase flow,Chemical engineering science, 60(22), 5917-5929.
E. V. Safronova and G. N. Abaev, 2004. Mass exchange in a jet vessel, Chemical and Petroleum Engineering, 40 (5), 317-323.
E. Loth, and G.M. Faeth, 1990, Structure of plane underexpanded air jets into water, AIChE Journal, 36(6), 818-826.
Y. Chisti, M. Kasper, and M. Moo‐Young, 1990, Mass transfer in external‐loop airlift bioreactors using static mixers, The Canadian Journal of Chemical Engineering, 68 (1), 45-50. 21.M. K. Zakharov and V. G. Ainshtein, 1997,Calculation of process of desorption from liquid mixtures when the pressure is discharged,Chemistry and technology of fuels and oils, 33(4), 202-206.
a. Investigations of lighter fluid jet injection velocity on dip depth formed at surface of heavier butt fluid, b. Communications:international conference on advances in mechanical and automation engineering-, Single air delivery through air onto water film, BS Yilbas,Shuja SZ, c. Zahid H. Khokhar, Mitteilungen Klosterneuburg Journal i. Single air delivery through air onto water film on flat bottom, ii. On first ignition in a covered metallic plate geometry, iii. Fast air jet reappearance within stagnant water layered at metallic wall boundary check, iv. Multiphase investigations of laminar air jet penetrations at stagnant surface of fluid layered at metallic bottom in a rectangular channel open on other side.
Zahid H. Khokhar, 1. Fuzzy modeling of surface developments of plastics: additive based; 2.On a built fuzzy interface reaction process: range change effects; 3. Fuzzy modeling of a reaction: Introduction of a change; 4. Graduation of polymer by fuzzy model: a new sample; 5. Polymer fuzzy open up processing.6. Mechanics of Composite Materials,MCM 2010.Institute of Polymer Mechanics: Sixteenth international conference: mechanics of composite materials: May, 2010 Riga, Latvia: Book of abstracts.
Zadeh, L. A., 1989, Knowledge representation in fuzzy logic, IEEE Transactions on Knowledge and Data Engineering, 1, 1, 89-100.
Zahid H. Khokhar, 1. Several injections in spite of a single injection comparative commentary , Wulfenia Journal, 2. Multiple injections into horizontal pipe Reduction in mixing downing length, Mitteilungen Klosterneuburg, Journal, 3. On the bravais lattice from the chorus of water shell within the tee cross, JMEST, Journal of Multidisciplinary Engineering Science and Technology, Germany, 4. Study of Numerous Injections into Horizontal Flow Stream at Low Temperature, Chemical Product and Process, Modeling, DGruter Journal, 5, 1,2010,27, 5. An experimental and numerical predictions of multiple injections into horizontal flow to reduce length required for mixing, Proceedings of the V European Conference on Computational Fluid Dynamics ECCOMAS CFD 2010, Lisbon, Jun 2010, 6. Book of Abstracts of the V European Conference on Computational Fluid Dynamics ECCOMAS CFD 2010, I and II, ISBN: 978-989-96778-0-7.
Zahid H. Khokhar, I. Effects of obliqueness of jet into horizontal flow, Mitteilungen Klosterneuburg Journal, II. On hot jet confinement into pipe flow: change in jet delivery angle, Ciencia ET Journal, III. On injection posture infused into body, Kasmera Journal, IV. Effectiveness of jet injection within Horizontal downstream, Mitteilungen Klosterneuburg. V. Effects of angle jet into horizontal pipe: Center Oriented, Jokull Journal, VI. On adjusting abnormal side hot injection into cold water constant continuous flow, Wulfenia Journal, VII. Side oblique jet mixing measurements in pipeline flow, Mitteilungen Klosterneuburg Journal, VIII. Symmetric co-and counter-angle injection into horizontal pipeline flow comparison.
RenekerD.,Chun I., 1996,Nanometre diameter fibres of polymer, produced by electrospinning. Nanotechnology, 7, 3, 216.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2016 gnpublication@
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
In consideration of the journal, Green Publication taking action in reviewing and editing our manuscript, the authors undersigned hereby transfer, assign, or otherwise convey all copyright ownership to the Editorial Office of the Green Publication in the event that such work is published in the journal. Such conveyance covers any product that may derive from the published journal, whether print or electronic. Green Publication shall have the right to register copyright to the Article in its name as claimant, whether separately
or as part of the journal issue or other medium in which the Article is included.
By signing this Agreement, the author(s), and in the case of a Work Made For Hire, the employer, jointly and severally represent and warrant that the Article is original with the author(s) and does not infringe any copyright or violate any other right of any third parties, and that the Article has not been published elsewhere, and is not being considered for publication elsewhere in any form, except as provided herein. Each author’s signature should appear below. The signing author(s) (and, in
